Welcome to Gem Equipments.

sales@gemindia.com - 9344455927

service@gemindia.com - 9366631697

Square Cooling Tower

Sufficient strength to withstand high velocities and vibrations

SALIENT FEATURES:

  • Design
  • Casing
  • Fill
  • Sprinkler
  • SCSP Nozzles
  • Drift Eliminator
  • Axial Fan
  • Motors
  • Corrosion Free
  • Light Weight
  • Installation, Service & Maintenance
Download Brochure
Square Cooling Tower

Design:

Evaporative (FRP) Cooling towers are of vertical induced draft counterflow design with uniform water distribution and optimal heat transfer. Towers can be installed independent of wind direction.

Casing:

The tower casing is made of tough fibreglass reinforced plastic (FRP) and has sufficient structural strength to withstand high wind velocities and vibrations. UV - stabilised resin is used along with gel coat for longer life. It is resistant to local impacts and even if slight damage occurs, local repairs can easily be done. The portion of casing housing fill and eliminator has a round cross section. The water collection sump, also of FRP, is leak proof & avoids water spillage.

Fill:

The fill is of rigid Poly Vinyl Chloride (PVC) and is of honeycomb design with very large contact surface area. The fill splits the air and water into several streams, increasing the time of contact and also heat transfer between water and air. The fill is in modules and is packed in the tower casing without any cutting for curves. The air pressure drop through the fill is negligible. The fills are available with flute height of 6mm, 12mm, and 19mm with sheet thickness of 1mm and 1.2mm.

SCSP Nozzles:

The performance of cooling tower greatly depends upon the water distribution over the fills. SCSP nozzles distribute water evenly through a wide spray angle without any dry pockets. They are lightweight and reduce the frequency of clogging. The Solid Cone Square Pattern (SCSP) nozzles produce a solid cone spray of water that is distributed in a square pattern onto the fills.

Drift Eliminator:

Reduces carry over losses of water. The eliminator is of rigid PVC (Applicable for square type cooling tower). The individual drift eliminators of S-shaped corrugated sheets are bonded with subsequent layers to create the structure. The entire area is thus divided into several fine S shaped mini zones each removing water droplets on the entire surface of the cell.

Axial Fan:

Specially designed energy efficient fans are of induced-draft axial type with adjustable pitch. Material chosen are non corrosive of plastic, FRP or aluminium alloy. The high efficiency design ensures low running cost and the lowest possible noise level. Fan blade pitch is factory set and dynamically balanced.

Motors:

The motors are totally enclosed (IP55), flange type, 415 V, 3 ph, 50 Hz, induction weather proof with SS304 extended shaft and are specially designed for cooling tower application.

Corrosion Free:

The tower casing is of FRP, fill and eliminator are of PVC, and SS304 fasteners are used, thus eliminating corrosion, the biggest enemy of cooling tower. All steel components such as motor support, water distribution pipes, hardware etc., are hot dip or spray galvanized.

Lightweight:

The towers are compact and light weight resulting in easy delivery to site and installation. Light weight also saves on structural and masonry. Roof installation can also be done without any special reinforcements.

Installation, Service & Maintenance:

Towers of lower capacity are completely factory assembled before despatch. At site the tower has just to be bolted, on the RCC / brick masonry foundation, thus saving a lot of installation time. Towers of higher capacity can easily be assembled at site and then installed in a manner similar to small towers. Maintenance is considerably reduced because fan, sprinkler fill and eliminator can easily be approached from the top without disturbing the cooling tower casing.

Technical Specification

Sl. No. Model Variance Motor Dia of Fan In / Out Size Overall Dimension Shipping Weight Operating Weight
L H P HP / RPM . NB LxWxH in mm kg. kg.
SCB-10 tick tick tick 0.5 HP / 1440 450 (PVC) 2" / 2½" 815 x 815 x 1600 80 220
SCB-15 tick tick tick 0.5 HP / 1440 450 (PVC) 2" / 2½" 815 x 815 x 1950 80 220
SCB-30 tick tick tick 1 HP / 950 750 (NL) 2" / 2½" 1130 x 1130 x 2235 235 790
SCB-40 tick tick tick 2 HP / 950 1000 (AL) 3" / 3" 1440 x 1440 x 2590 255 805
SCB-60 tick tick tick 3 HP / 950 1000 (AL) 3" / 3" 1740 x 1740 x 2810 310 1070
SCB-100 tick tick tick 5 HP / 950 1400 (AL) 5" / 5" 2130 x 2130 x 3100 575 1675
SCB-150 tick tick tick 5 HP / 950 1400 (AL) 6" / 6" 2650 x 2150 x 3200 690 2075
SCB-200 tick tick tick 7.5 HP / 710 1800 (AL) 8" / 8" 2650 x 2650 x 3225 950 2200
SCB-250 tick tick tick 10 HP / 710 1800 (AL) 8" / 8" 3150 x 2650 x 3350 1075 2340
SCB-300 tick tick tick 12.5 HP / 600 2200 (AL) 8" / 8" 3150 x 3150 x 3500 1270 2605

Note: SCB Model variance from 100 to 300 TR are also available

* Product Design and specifications are subject to change due to constant upgradation.

x

NEED HELP?

Live Chat
Agents are offline

send enquiry

captcha